All Forum Posts

Hi. I own a 1937 Model 18. I purchased the bike missing a rear drum brake torque arm. I have failed to try and source one so now i'm looking to see if any other arms from different manufactures will do the job.

My sons Atlas Has been fouling plugs with sticky brown shiney stuff (again). We thought we had this under control with buying the top grade esso which we are assured contains no eth.

On checking the cylinder head on my 1958 domi I noticed the oil return hole under the right hand inlet valve spring assembly has a small steel plug in it.

can anybody please help me with what the rear wheel fitting for a sidecar chassis looks like for a 1952 es2 plunger frame

Just putting together my Model 50 following a major rebuild - trying to get clutch working. There appears to be too little movement on the clutch push rod. I am wondering if I have misplaced something during the reassembly.

Hello,

Hello,

Hello,

Hi All, ive been offered The same mk 3 interstate that was hoping on purchasing last year, ive taken another look at it and its pretty good, there are a few things that will need replacing and i can see me spending roughly £2000 on parts not allow

I have a problem with my Mk3 Commando, it wont rev above 4500 in 4th gear.

searching the internet for some new barrels and pistons for me domi engine cant seem to find anything. when i did me triumph engine there were loads to choose from and still is.

Barry

My speedo was very dirty inside glass and trip reset was loose inside case. So the hard bit, tried to remove bezel by all the mean i could find online no luck. So cut a slot in the bezel to remove, part on order £24 with glass and seal.

Spotted this unfortunately a bit to far for me. Hope the rider was ok.

https://www.copart.co.uk/lot/32741977/Photos

Hello everyone,I'm having some tuning problems with my 72 combat.

As per the title really, I'm looking for part number 78 on the below diagram.

This has probably been answered but can a Smart Battery Charger be left permanently connected in the charge mode?

I have to go away for two weeks, will it cook my battery if left connected?

Many thanks Roger

My engine has been in a box for years and camshaft got some surface rust, Cleaned it with fine wet n dry (see photo) some fine marks left can i keep cleaning?

Hi. I have a Slimline Dominator that is in Cafe Racer trim and I want to turn it back to near standard. Unfortunately, it was originally a "Deluxe" model, so it does not have the "spikes" on the upper Frame X-tube for the front seat fixings.

Does anyone know of a source for a used original or an accurate repro of this item?

I've tried all sources I know of in the U.S. without luck.

Thanks,

Ed

Has anybody else taken delivery of a new Euro 4 961? if so I would be interested to have a conversation!

Cheers Nigel

We took the 99 and Atlas out yesterday for a run round kent lanes, both have had problems of late ,and at times it seems we make things worse by tinkering, we were switching bikes ,spark plugs and twidling carb screws.

Having just completed my rebuild and covered around 500 miles I decided I should bite the bullet and add up all my receipts.(ouch!). I thought members might be interested and have analysed the figures into broad areas.

The Lads have been whinging that I don't always cancel the indicators on the 99, so I have fitted a bulb in the HL shell ,thought it a simple thing to wire it into the supply from the blinker unit to the HBar left/right switch, Nope !

Hi,

This is my 650SS frame, I have attached a photo, to show what it was like before someone, powder coated it a finish i personally dislike, as I do black frames!

Hi,

Does anyone know whether the later 8" BSA/ Triumph Conical Hub Twin Leading shoe brake plate unit and shoes, can be adapted for a Dominator full width 8" drum?

Cheers

John

Fitted valve guides, spring seats are now a little large over the guide, do i need to buy the smaller holed seats, or not?? ,RGM state they are interchangeable, the plot thickens !

hello ! can anyone help me out with photos of a p11a(68) frame ? mine has been butchered/welded and i would like to know what i have to do to make it good again with the help of photos .the damage is on the top rear of the frame.

thanks

on my recently acquired es2 [56 frame, 59 engine] the clutch basket is rubbing on the back of the chaincase.

should there be a spacer on the spline?

Hello All,

Hello All,

I purchaed a seal from the spares schem (for the sleeve gear). It looks to be the one in the picture by the markings on the outside. It part number 041267 and it seems to be common to all manner of AMC gearboxes.