All Forum Posts

Hi,

I noticed this: https://www.ebay.co.uk/itm/Norton-Lay-Down-Laydown-Gearbox-International-ES2/264288592223 for what looks like a reasonable pric

Hello there,

I'm going to send my barrel to a workshop to rebore, this time the value are really off limits.

I've got an +0.40 piston NOS from Wellworthy.

Can anyone identify the O-ring that resides in the groove of the tachometer drive gear?  The description on the Andover Norton parts list for the drive gear (part-no: 06.5201) states:

Bike is a 1959 Domminator '99'

1. What is the recommended method for removing old, and replacing with new, small end bushes ?

2. What is the torque setting for tightening big end bolts ?

Had a great ride out last week, 100+ miles including a ride over Wrynose and Hardnott passes.

I'd just like to say thanks to the NOC shop team members, for a group of volunteers they are doing a great job.

Is there any information oan the rally near Rimini to be had? I have emailed but await a reply, just wondered if there is another way through the club for information.

Well, my happiness at getting my Electra running after it's 25+ year rest has been interrupted by an oil leak from between the fins on the right head.

I know this is an issue much discussed in the past but I can't quite pin down the discussion thread that gives the definitive answer.  My old Wipac alternator has finally died and having already converted the bike to 12v electrics I want to replac

I wonder if someone could tell me, would an original 1968 Norton fast back in green with grey side panels have any writing on the side panels???

Hi

Can someone help me with information on the head steady on my '61 ES2.

Can the gearbox be removed from a 1956 Dominator 99 without having to remove the gearbox and engine as a unit ? I.e. leave the engine in position.

Iv'e got a 1955/56 ES2.the frame has been powder coated and I can't find the number,were should i be looking.Thanks.

Here’s a deal to be had, straight thru short stubbies & a decat pipe ,and Dom seat https://www.accessnorton.com/NortonCommand

Hi all - I am preparing my 1972 manufacture 750 Combat Cylinder Head for bead blasting and am looking for conformation on the number of oil ways so that I may block them as well as possible then clear and clean them afterwords .

So what was the outcome from the Club AGM in Liverpool? I delayed phoning a couple of people expecting that there would soon be news and chat on here, but it's all very quiet. I could not attend due to a major family commitment.

My son's Honda CBR600RR didn't start after the winter. So he simply borrowed one of my bikes and went away to first track day for the year. Leaving the plastic missile in the workshop. Figured out that most probable was fuel pump fail.

Hi got a problem when engaging first geat the gear dogs catch the kickstart gear and jam the gearbox up ,only happens in first have riddenthe bike a good few mile using 2nd 3rd and top with no problems ,any body got any parts for sale ,main shaft

I'm an extraordinarily disorganized person and I can't find any of the three repair manuals I own for my 1971 Roadster.

I want to test the output of the alternator on my Mk2a Commando, using a multimeter can anyone tell me what readings to expect assuming all is well?

A friend has an 850 Mark 2A and it is jumping out of 4th gear when the bike gets to about 50mph (80kph). Either into neutral or sometimes back into 3rd. I've done some research but most relate to jumping out of 1st gear.

I phoned ANIL up with a list of bits I needed and went down to collect them 2 hours later. Although they are busy, there was time for a short natter. 

All the parts were clearly identified, well wrapped, and fitted perfectly.

After previously owning a '75 Commando, I bought a '65 Electra project in October that had been sitting for 25 years and had not started before that for an unknown period.

Hi, Does anybody know the angle of the valve seats for the 350 Navigator 1961. Only I am looking to buy a re-seating tool.

Many Thanks.

Hi,
Could anyone please help with detail of the exhaust valve lifter parts for a 1930 500cc overhead valve Norton?
My model 20 is missing the complete assembly which I think consists of three parts.

Southern Branch Ride Out - Sammy Millers

Hi all,

I recently revived a 1963 norton electra that was sitting 

in a garage in parts for 30 years finally i got the bike to 

start and it runs very well , next i wanted to put the bike

What ammeter was fitted to the 1959 Jubilee. Was it Lucas, ive seen a couple of Jubilees that look like they have had a Miller type unit fitted.

Thanks

John.