All Forum Posts

Bike is a 1959 dommi '99'.

My splendid old Commando has travelled far and wide with me and I would not be without it - but - every time I get on it after riding my BMW GS I feel as though it has no brakes!

hi

Hi 

I'm building a dominator into a cafe racer and like the external fork spring look do I need to remove the internal springs and can I buy light external springs just for the look

cheer for any info

Tongs for hairspring valves. Fine blacksmith work. They are so beautiful that I shall find a place to hang them on the wall on the house. 

I am looking for advice in a good quality H4 lens / reflector - my correct original Lucas BPF lamp is just too pathetic and scary at night.

Today I went to a company in Kent, and took along a pair of Manxman silencers, mufflers. The owner inspected the silencers, and how they were made. After about five of so minutes deliberation, I was given a price of from £380 to £410 each.

Has anyone fitted an American made JRC carburettor to a Commando. My 1976 Commando has a single Mikuni fitted and although it has been set up on a rolling road it gives me a lot of problems when starting up?

Paul Dunstall / Cafe racers wanted

es2 what fuse ,earth side or live side.6volt

Hi,

This press photo is on eBay at the moment...There is nothing that I can add really :-)

Sadly, 419 VRR is on a Mercedes now. I hope that the bike is still out there somewhere.

Looking for a bettery box lid for Navigator, none in NOC shop, if any one has one they are prepared to let go please pm me.

Thanks

Andrew

Hi. I have two slimline frame petrol tanks, both still in the original grey/silver paint.

A pre-emptive solution by my late old friend Bernard Harding: car collector  motorcycle collector, and owner over the past few decades of 1926 16H, 1927 Model 18, 1932 Inter, 650SS, NorImp(!), plus many others ... sadly missed.

Hi all - I am in need of advice regarding ring orientation. I am installing new Gandini ring sets as supplied by Andover on original AE Hepolite pistons . 

Just in the process of replacing the magneto chain on my 1935 Es2. I found that the chain fitted was a 44 link chain and was very slack. Checking this out I discover it should be a 42 link with 15 tooth sprockets.

When I load the site I'm getting a message (Firefox) that its security certificate has expired!

Evening All.

Is just me or is anyone else having difficulty  accessing the NOC Shop on this web site?

I have tried over several days now but keep getting the same message "Internet Server Error"

Bike is 1959 Dommi '99'

Bike is 1959 Dommi '99'

Just completed a full engine rebuild and, after about 15 miles of running, I have two problems.

Any recommendation for the best crankcase jointing compound thesedays or the best way of keeping these engines as oiltight as possible (650SS) ?

Hi Guys, Preparing to rebuild my 1967 650SS engine.  My trusty Haynes manual shows a nice picture of the conn rod and states 'oilway MUST face outwards - late 650 and 750  engines after engine number 116372.' However, when I stripped the engine th

Hi all ,

Hi all,

This is probably a silly question, but could someone tell me what the 2 little H59 screws are for that screw into the headstock / headlug of the slimline featherbed frame?

1949 Inter clutch

I registered my Navigator yesterday so it is street legal for Germany!

Today I made a 10 mile test ride. Stopping for a nice photo spot I noticed oil all over the bike. So no photo but going back to my workshop.

Being new to SV engines, can someone advise on the correct grease for the valve lubrication also how often, I have been told copper grease and at every start up but not confident.

Hi all. Thought you might be interested in photos of my 4 year completion of my jubilee

Hello Global Norton Enthusiasts,

What is the correct length clutch push rod length using no pushrod mushroom.  I have a vertical gearbox with an AMC clutch.  Thanks.

Josh Fribley

Columbus,  OH USA