Skip to main content
000000 000003 000006 000009 000012 000015 000018 000021 000024 000027 000030 000033 000036 000039 000042 000045 000048 000051 000054 000057 000060 000063 000066 000069 000072 000075 000078 000081 000084 000087 000090 000093 000096 000099 000102 000105 000108 000111 000114 000117 000120 000123 000126 000129 000132 000135 000138 000141 000144 000147 000150 000153 000156 000159 000162 000165 000168 000171 000174 000177 000180 000183 000186 000189 000192 000195 000198 000201 000204 000207 000210 000213 000216 000219 000222 000225 000228 000231 000234 000237 000240 000243 000246 000249 000252 000255 000258 000261 000264 000267 000270 000273 000276 000279 000282 000285 000288 000291 000294 000297 000300 000303 000306 000309 000312 000318 000321 000324 000327 000330 000333 000336 000339 000342 000345 000348 000351 000354 000357 000360 000363 000366 000369 000372 000375 000378 000381 000384 000387 000390 000393 000396 000399 000402 000405 000408 000411 000414 000417 000420 000423 000426 000429 000432 000435 000438 000441 000444 000447 000450 000453 000456 000459 000462 000465 000468 000471 000474 000477 000480 000483 000486 000489 000492 000495 000498 000501 000504 000507 000510 000513 000516 000519 000522 000525 000528 000531 000534 000537 000540 000543 000546 000549 000552 000555 000558 000561 000564 000567 000570 000573 000576 000579 000582 000585 000588 000591 000594 000597 000600 000603 000606 000609 000612 000615 000618 000621 000624 000627 000630 000633 000636 000639 000642 000645 000648 000651 000654 000657 000660 000663 000666 000669 000672 000675 000678 000681 000684 000687 000690 000693 000696 000699 000702 000705 000708 000711 000714 000717 000720 000723 000726 000729 000732 000735 000738 000741 000744 000747 000750 000753 000756 000759 000762 000765 000768 000771 000774 000777 000780 000783 000786 000789 000792 000795 000798 000801 000804 000807 000810 000813 000816 000819 000822 000825 000828 000831 000834 000837 000840 000843 000846 000849 000852 000855 000858 000861 000864 000867 000870 000873 000876 000879 000882
English French German Italian Spanish

TT carb.. today's lesson

Forums

Slowly I learn. 

Lesson 1: if the bike won't start in one or two kicks, don't waste energy but feed it with a fresh plug. Keep a plug and spanner in your jacket pocket. You know it makes sense! Don't give up and buy a Mikuni.

Lesson 2: if you want a TT to tickover steadily, don't butcher the slide  but add a set screw on top of the jet block. You will have the most inaccessible possible throttle stop, but it works perfectly and it totally unaffected by handlebar movements (unlike hanging the slide off the cable).

Attachments
Permalink

My TT carburettor came with a purpose-made cable which prevented the slide from bottoming out.  It also led to a situation where if you turned the handlebars once it had started it would cut out or the revs would increase depending in which direction you had turned the handlebars.  My learning curve [roughly equivalent to a 1-in-3] was that the carb is designed for that area between 4,000 and 6,000 rpm.  The supplied 5 cutaway and 350 main jet led to very brisk acceleration.  

A late friend spent two years trying to get his single to work with the TT carburettor.  His results were that he could get his machine to start easily but it would run atrociously, or it would hardly ever start but ran fantastically.  He had the patience of a saint [and a fair amount more] but eventually fitted a suitable Mk.1 concentric and it ran superbly.  When he sold the machine the TT went with it and the new owner fitted it back onto the machine and then complained that it wouldn't start!

Good Luck! 

Permalink

I run an Italian machine with a Dellorto SSI which is the same design as the TT , The only way to start is to flood till fuel drips,catch it on the throttle and hold a quarter open till the excess fuel is used ,then keep rolling the throttle . No use in traffic. When stationry keep the bike leaned over to the right .Not easy with a right side gearchange.

Permalink

They are both lever taps thanks Robert. Just 2 days before we were all imprisoned I nearly filled the tank, so I'm not keen on draining such a large amount of fuel. Although if it leaks enough it might be worth it!

PO fitted a cable stop but, as Colin says, tickover would change as I moved the bars, and it was always unreliable.

I keep blaming my starting problem on the carb  but actually it is solved by a fresh clean plug. I keep worrying about the oil control piston ring. It smokes when at tickover and pulling away from traffic lights when it is hot. It doesn't seem to leave a smoke trail on the road. Could it be the rather generous valve guide lubrication system? I've never seen direct oil injection into the valve guides before.

Permalink

Although I know some singles I've not had a Norton , but that sounds very likely .if the plug is not oily then it could be the exhaust guide.

Permalink

Is the "TT" carb really suitable for the "New" normal road use as it's name suggests,  spirited riding and bump starts?

 

John

Permalink

Its really only for racing,but some do make it work well enough for a  classic ride away from traffic.  The main problem is it turns you into a hooligan, I once tried to ride the Mayday run from Locksbottom to Hastings.The journey was frought with a thousand Jap crotch Rockets and police traps,I can't  do Traffic with that bike so made myself unpopular by overtaking all and sundry in all the wrong places ,"sorry can't stop"  get out of the way!. A bit like the pioneer LB run. Lucky not to get pinched. Better off with an Amal 289.

Permalink

It seems to be fine on the road. Not found any flat spots. They have numerous settings to play with and they are probably pretty hopeless if worn out. The air slide acts over the whole range so you can effectively change the main jet size on the road. Sounds a good way to burn holes in pistons...allegedly they tuned the race bikes to run fully open (maximum air), but closed the air inlet  a bit for the first few miles to enrich the mixture before the engine was fully hot. (I've been doing lots of reading in lockdown). Amal claimed the TT had to be flexible because "there's always a Governor's Bridge".

I suspect the main  drawback is the huge choke size, so low speed torque is probably not as good as with a smaller size. That makes the bike thirstier as well. The Inter has bags of torque and isn't as heavy as my Dommie 88SS, so even though in theory the Inter isn't as quick it certainly feels like it is.  I don't think the TT would suit the 16H.

Permalink

I run a 1957 Model 30 with a 10TT.9 and I would really like it to start easier without popping and kicking back!

My bike is an ex-road racer so the carb is probably right for racing as once she's running she runs great.

My carb has the following components: 320 Jet, No. 5 Throttle Valve, 109 Choke Jet, Jet Needle appears to be a porely stamped No.5 (or possibly a 6) and is clipped 2nd notch down out of 7 notches and looks to have always been there with the wear, and my Pilot Needle is 10 notches out (about a 1/4 turn) but my Plug comes out quite black as though its running too rich. 

I have a Champion OE068-N3C plug but I've gone hotter with an N4C and might even go up to an N5C to see how it works?

I am open to trying any ideas in the quest to find easier starting, even changing any carb settings or components, and I will resist swapping the TT for a concentric for as long as I can.  If I have to change the Carb, what model and settings do I need for an easy life?

I'm not looking for her to tick over without using the throttle screw just consistant easy starting.

Thanks

Permalink

I'm check my settings later today. But my pilot screw is a lot further out than that.

I seem to have got over my starting issues at present. Maybe it's just the warm weather. But I now have a very fixed routine.

My advance lever is marked at 42deg BTDC. I back it off just under 1/4". Fuel on, close the air lever, tickle the carb, fuel off again so it won't flood too much. Then usual up and just over compression, almost no throttle, and give it a go. As soon as it catches  advance the ignition immediately, open the throttle very slowly, and remember to reopen the fuel tap. As long as the bike knows there is a spare plug immediate to hand, it starts straight away. If it doesn't, then don't continue kicking for too long...change the plug. It seems to tun best with the air lever about half open, but I ought to do some proper checks. Not east to do plug chops etc on the ridiculously busy roads. Any hints would be welcome.

I found it worth playing with the pilot..since it is richer when screwed out, I adjusted the tickover to get the best it will do  but erred on the side of further out. I can't be sure but I think it's nearly 2 turns out.

On the road it's just like any other carb. Apart from fuel leaks  which are worse.

Good luck!

Hi David,

If you’ve had the opportunity to check your settings I’m very interested to know what they are?

I’ve also purchased Amal’s Parts and Settings book and await for it to arrive via snail mail.

Can you advise how you set the degrees on your advance lever?

Thanks

Andy

Permalink

Andrew...just looked up my settings. 1932 Inter. Comp ratio I think is 8.5.

Needle. 7 notches, set in middle notch (no. 3 from top).

Slide. Cut away no. 6 (3/8").

Main jet 320.

Needle jet 109.

Carb is marked 34/041.  10TT34.

Pilot needle is I think about 2 turns out. I played with it a few weeks ago and I opened it up quite a lot from the 1.5 turns I started with. It made quite a big difference to tickover speed, unlike the 276 on my 16H where the pilot screw has almost no effect.

Plug is NGK B6ES.

Differences between yours and mine aren't much apart from pilot screw. You probably know slides are very expensive, and if the carb has been resleeved then a standard sleeve probably won't fit anyway.

I did have starting issues but they seem to have receded. Partly I think because of opening the pilot, partly because I now know exactly where to set the ignition.

I usually start with the air slide down, but open it to mid way to run. Otherwise it bogs down.

 

Timing is 41deg BTDC on full advance. I've put a thin paint line across the lever and disc to make it clear. I back off by about 3/16 inch (4 to 5mm) to start. Any less and there's a risk of savage kick back. Much more and it becomes more reluctant.

Actually I timed it with about 1mm left to pull on the lever, hence the line. (Measured at the edge of the middle disc on top of the lever)

With my jet block top screw, tickover is too fast on full advance, at about 2000rpm. But it drops to well under 1000 when I retarded the lever. I want to slow it a bit to make it easier to engage first gear from a stop without retarding it quite so far. The TT of course wasn't intended to be used at a standstill.

Hope this helps. I've stopped worrying about stopping and starting it now. (If course it might just be the warm weather...)

In reply to by david_cooper

Permalink

Taank you David for all the information.

All being well the weather will be better in Inverness and I'll be able to play!

II obviously have a note of my settings, but I'll reset the carb as you've detailed and see what happens, and all being well she'll burts into life very quickly.

Another question though, or more an observation... I have noticed that the underneath of my fuel tank gets quite wet above the open bell mouth, is this to be expected with the amount of fuel that must pass through the TT?

Have a good weekend. Andy

Permalink

Thats blowback from valve timing more suitable for the race track. Sometimes it can be reduced by  a different exhaust  ,but the cure is to either rev it more (race!) ,or  change the cam/ or cam  timing. The bike will also be easier to start with  milder valve overlap. And be more powerfull at the revs used for road riding.I have the same issue on a 250 OHC ex race bike I use on the road. I will swap the wild overlap low lift ultra revvy cam for a high lift road cam.Can't do much about the 40mm inlet valve and 29mm carb.

Permalink

I have an annoying amount of fuel leaking onto the oil tank, usually stops once it fires up. I've not looked upwards! I now turn the fuel off again after turning it on, and flooding it a bit. Then turn it on when it fires up. It's better now since I flatted the sides of the banjo which were not quite parallel.

An air filter is of course a good idea. It not only preserves engines but saves fuel because any that spits back is re-breathed. I've never seen one on an Inter, but long bell mouth should have a similar effect on reducing spit back.

Permalink

The other issue with blowback is the fueled up air goes back in the  carb and picks up yet  another charge of fuel , so at that rev range the mixture will be very rich  and any attempt to tune out the issue by weakening the carb will produce a weak spot  somewhere else. Not nice for pootling around the lanes. No issue at all at 110 mph down Bray Hill.------Why only 110 ?, I now have the attention span of a gnat ,so have to set personal limits!.

 

Permalink

I’m still playing trying to find better starting settings with my 10TT9 carb and don’t seem to be getting anywhere fast using David’s settings as a starting point and may have to resort to changing for a 289 carb?

Please excuse my ignorance (as basically I’ve been a 2 stroke person until I got my Inter), but I’ve been reading various threads and If I’m reading correctly the Cams and exhaust type can majorly effect the carb settings.... in what way are the settings affected?

My exhaust is a Goldie style with a stubby tail/outlet, but how do I determine what Cams I have without stripping the head down (is this even possible)?

Thanks 

 

Permalink

I can't help with cams, but I'm fairly sure the exhaust won't affect running until the revs start to rise.

My starting problems seem to have gone away. After a couple of turns with the decompressor just released enough to get it over TDC it started yesterday on first kick following my usual routine. I never blip the throttle. I think timing is more critical than anything. The old adage...most carb probablems are caused by timing. How is your ignition timing?

Permalink

Just with playing with the pilot screw (coming gradually out) I have been starting from hot and cool but only time will tell and the proof will be the next time she comes out if she starts!!

Come the end of the day she was sitting ticking over nicely high prompted me to get my helmet but not managing to leave the drive as the clutch plates had stuck together with lack of use, the clutch has also now been stripped, cleaned and hopefully now ready for when the dry weather returns to the Highlands. 

yes, I use the decompressor to pass just over TDC but I do find that I need to flood the carb to be able to start.

I haven’t played with the timing, all I’ve done is check my plug gap and I’m a great believer with my Inter that if it’s not broke I won’t fiddle with it but to be honest I am nervous about when I do need to touch the timing as it’s totally alien to me compared to the Japanese 2 strokes of my youth.

 

Norton Owners Club Website by White-Hot Design

Privacy Policy